Takeoffs, done for you

Send your plans.Get the takeoff.

Your plans in. A clear, CSI-coded Excel schedule out. We measure the drawings, organize the quantities, and flag what needs a second look.

From $49Fixed per project. No subscription.

  • 11 trade scopes
  • CSI 01–32 coverage
  • PayPal or card after upload
From drawing to deliverablePDF → XLSX
The drawing. The markup. The quantities.Illustrated with our Fircrest sample. Explore the real output ↗
Built by a builder. Andrew Burges — builder, truss builder, engineered lumber, home improvement PlanSwift and Beam AI, compared
The plan, up close

Every tag, located and read.

Sheet E-2 from a published municipal bid set. The highlight boxes are anchored to the sheet's own text coordinates, so the markup lines up with the drawing rather than approximating it.

Before and after

Drag the slider. On the left is sheet E-2 as issued. On the right is the same sheet with the tags TakeoffIO located, read, and carried into the quantity schedule.

  • 01Existing panel
  • 02Master control panel
  • 03Automatic transfer switch
  • 04SCADA
  • 05Utility meter
  • 06Transformer
  • 07Pump control panel
  • 08–11Pumps and level controls
  • 12Float switch

Source: City of Fircrest 44th St & 67th Ave Lift Station bid set, sheet E-2 (public record). Markup is anchored to the sheet's own text coordinates.

Sheet E-2 of the Fircrest lift station bid set, original one-line electrical diagram
The same sheet with twelve numbered orange highlight boxes on the electrical equipment tags
Original sheet Takeoff markup

Drag or use arrow keys to compareFircrest Lift Station · E-2

From marked-up plans to an Excel schedule

Four rows from the Fircrest workbook. Each quantity points back to its source sheet. “Verify” flags an item that needs a second look.

Download sample Excel
ItemCSI codeDescriptionQtyUnitSheetStatus
6126 32 23 00Automatic transfer switch, 150A, 14KAIC, solid neutral, programmed delay transfer1EAE-2, E-6Scheduled
6226 33 00 00Utility transformer, 75 KVA, 240/120V, 3 phase, 4 wire1EAE-2Scheduled
6311 53 13 00Submersible wastewater pump, 7.2 HP2EAE-2, E-4Scheduled
6526 60 00 00Float switch, high level3EAE-4Verify

How it works

Three steps. No new software.

  1. 01

    Upload vector plans

    PDF or DWG from your design team, with the scope you need. Original exports only — no scans, screenshots or phone photos.

  2. 02

    We run the takeoff

    Each scope is measured from the drawings by geometry code, which also does the arithmetic. Every quantity traces back to the sheet.

  3. 03

    Get the schedule

    An Excel-ready, CSI-coded schedule grouped by trade, level and location. Ambiguities are flagged for review, never quietly guessed.

Simple, project-based pricing

More help with the bid. No strings attached.

Three fixed prices. Pick the one that matches your plan set. No ongoing subscription, no per-seat licence, and no custom quotes.

One Trade
$49fixed / project

For one trade on a plan set, when you need quantities fast.

  • AI-assisted quantity takeoff
  • One trade scope
  • Trade-based line items and practical units
  • Excel-ready output
Choose One Trade

One scope, one schedule.

Multi-Trade + Review
$249fixed / project

For bids that deserve a professional review before the numbers go to work.

  • Everything in Multi-Trade
  • Review by an estimating professional
  • Quantity, unit, and scope-alignment checks
  • Flagged details and clarifications reviewed
Choose Multi-Trade + Review

An estimator checks it before it ships.

All prices in USD. Fixed per project — no per-seat licences, no custom quotes. Send your plans, pay, and we will start your takeoff.

What shapes the job

Four things we read first.

Your tier sets the price before we open the file, and it does not change. These are what we look at in your plan set, because they decide how much drawing there is to measure and what we confirm back to you.

Drawings

Sheet count and drawing quality

Legible, scaled drawings move faster than a low-resolution export. Unreadable or mixed-scale sheets can mean a manual re-measure.

Trades

How many trades

One trade is a focused scope at the One Trade price. Multiple trades on one plan set are covered by the Multi-Trade tiers.

Size

Size and complexity

Floor area, building height, and the number of plan sheets all affect how much measurement is in front of us.

Review

Review level

Adding an estimating professional's review moves you to the Multi-Trade + Review tier at a fixed $249.

Scope coverage

Eleven scopes. One plan set.

Measure one trade or combine several. Each line lands in the same CSI-coded schedule, grouped by trade, level, and location.

09 Drywall & framing Board, studs, insulation, finish What we measure
  • Gypsum board by type and thickness
  • Metal stud framing by gauge and spacing
  • Top and bottom track
  • Shaft wall assemblies
View scope →
26 Electrical Devices, conduit, conductors, lighting What we measure
  • Receptacles, switches, and devices
  • Light fixtures
  • Conduit by size and type
  • Conductors by size and type
View scope →
03 Concrete Footings, slabs, walls, reinforcement What we measure
  • Footings by type
  • Slabs on grade and suspended slabs
  • Walls and columns
  • Reinforcing steel
View scope →
22 Plumbing Pipe, fittings, fixtures, specialties What we measure
  • Domestic water piping by size and material
  • Waste and vent piping
  • Fittings and transitions
  • Plumbing fixtures
View scope →
23 HVAC Ductwork, equipment, diffusers, controls What we measure
  • Supply, return, and exhaust ductwork
  • Duct fittings and transitions
  • Diffusers, registers, and grilles
  • Air handlers, rooftop units, and fan coils
View scope →
09 Flooring Finish flooring, base, transitions What we measure
  • Flooring area by finish type
  • Tile and stone by size and pattern
  • Base and wall trim
  • Transitions and thresholds
View scope →
09 Painting Wall, ceiling, and trim coatings What we measure
  • Wall area by room
  • Ceiling area
  • Doors and frames
  • Trim, base, and casing
View scope →
06 Lumber Framing lumber, sheathing, hardware What we measure
  • Wall studs by length and grade
  • Floor and ceiling joists
  • Rafters and roof framing
  • Beams, headers, and posts
View scope →
06 Decking Boards, joists, clips, flashing What we measure
  • Decking boards by area
  • Joists by size and spacing
  • Beams and girders
  • Posts and footings
View scope →
06 Porches & railings Posts, beams, stairs, guardrail What we measure
  • Columns and posts
  • Beams, headers, and rafters
  • Stairs by rise, run, and width
  • Guardrail and handrail length
View scope →
06 / 12 Cabinets & millwork Casework, tops, trim, hardware What we measure
  • Base cabinets by size and type
  • Wall cabinets by size and type
  • Tall cabinets and pantry units
  • Countertops by area
View scope →
+ Something else? Tell us the scope and we will confirm it before work starts. Tell us the scopeNot on the list? Send the plans and the scope you need. We will confirm coverage before work starts.Start upload →

Open a scope to see what we measure, the drawings we need, and where bids usually go wrong.

Side by side

The honest comparison.

Based on publicly available information as of November 2026. Verify current features and pricing with each vendor.

What matters
PlanSwift
Beam AI
TakeoffIO Our pick
Pricing model
Annual licence — $2,000 Essential, $3,000 Core
Annual licence — from $8K/yr per trade (DIY), from $25K/yr done-for-you
$49–$249 fixed per project
Who does the takeoff
You trace it in their software (Core adds Auto Takeoff)
Your team on their DIY tool, or theirs (done-for-you)
AI plus optional human review
Subscription required
Yes — annual licence
Yes — annual licence or Enterprise contract
None
Turnaround
First pass in minutes on Core; you finish it
24–72 hours, done-for-you
Confirmed after plan review
Deliverable
Your own takeoff file
Excel estimate
CSI-coded Excel plus quantity schedule
Trades covered
Every trade, with pre-built assemblies
All trades done-for-you; DIY covers HVAC, plumbing, steel
11 scopes, one schedule
Addenda and revisions
Manual updates
No public claim — ask them
Measured from the sheets you upload
Human review
You
QA-checked on done-for-you
Optional $249 tier
Setup and training
2 hours live 1-on-1 training included
Free, unlimited training; support team
None — upload and go
Best for
Estimators who want a tool
Teams buying takeoffs at volume
Small–mid contractors who bid often

PlanSwift and Beam AI are trademarks of their respective owners and are used for identification only. Comparison reflects publicly available information as of November 2026 and may change. TakeoffIO does not claim affiliation with either vendor.

Go deeper: TakeoffIO vs. PlanSwift · TakeoffIO vs. Beam AI · Takeoffs from $49

Questions

Before you switch.

Is TakeoffIO a replacement for PlanSwift?
For contractors who want finished quantities instead of another measuring tool, yes. PlanSwift is software you operate to trace drawings yourself. TakeoffIO is a service: you send the plan set, and you receive an organized, CSI-coded quantity schedule you can price from.
Do I need a subscription to use TakeoffIO?
No. TakeoffIO is priced per project: $49 for a single trade, $149 for multi-trade, and $249 for multi-trade with estimator review. There is no monthly seat, no licence, and no custom enterprise quote.
What do I actually receive?
An Excel-ready quantity schedule with trade-based line items, CSI codes, units, and quantities, grouped by trade, level, and location. Scope notes and flagged ambiguities are included where the drawings require a decision.
How accurate is an AI-assisted takeoff?
The AI extracts quantities from the plan set, and the output is organized for review against the drawings. On the Multi-Trade + Review tier, an estimating professional checks quantities, units, and scope alignment before delivery. You remain responsible for final pricing and bid decisions.
Which trades do you cover?
Drywall and framing, electrical, concrete, plumbing, HVAC, flooring, painting, and lumber are the core scopes, with decking, porches and railings, and cabinets and millwork bringing the total to 11. Multi-trade plan sets can combine several of those scopes in one schedule.
Can you work from a scan or a phone photo?
No. A scan or phone photo is a raster image: it has no vector linework, scale, or readable text layer to measure against. If that is all you have, tell us before you pay and we will either arrange a manual review or decline the file rather than present an OCR guess as a takeoff.
How does the takeoff model work?
A custom-tuned Qwen 3.5 model reads the sheet and selects from 50 measurement tools, writing geometry code that measures lengths, areas, and counts straight from the vector linework. The code does the arithmetic, so the language model never invents a quantity. Assembly assumptions cite the code sections they follow, but that is a measurement basis, not a code-compliance certification.
How is TakeoffIO different from Beam AI?
Beam AI sells annual licences: from $8,000 a year per trade for the DIY software tier, and from $25,000 a year for the done-for-you tier, with a custom Enterprise tier on top. TakeoffIO runs a done-for-you model at a fixed per-project price, with human review as an optional tier instead of a licence you pay for whether you bid or not.
Make the next bid lighter

Your next bid doesn't need another late night.

Send your plans, then choose your trade scope and pricing tier.

  • Vector PDF & DWG
  • From $49 fixed
  • Optional human review
Drop your construction plans here

Vector PDF or DWG · up to 50 MB

Original exports only — no scans, screenshots, or phone photos.

You can pay by card or PayPal after uploading. We confirm your delivery window after reviewing your plans.

Plans are uploaded over an encrypted connection and stored privately. We delete uploaded files 30 days after your job closes, and 90 days after submission if it never closes. Your drawings are used only to produce your takeoff.